Zigbee2MQTT: USB passthrough not working

[navels]

I am trying to move Zigbee2MQTT from a Home Assistant addon to an LXC container. I have tried both the Zigbee2MQTT and Alpine-Zigbee2MQTT scripts, both with Privileged mode selected in the Advanced Settings, but cannot get my Sonoff Zigbee USB stick to show up in /dev/serial/by-id.

The device is detected in Proxmox:

# usb-devices 
...
T:  Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=10c4 ProdID=ea60 Rev=01.00
S:  Manufacturer=ITead
S:  Product=Sonoff Zigbee 3.0 USB Dongle Plus
S:  SerialNumber=2a3900394845ed11bea1c68f0a86e0b4
C:  #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=usbfs
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
...

I had this all working with HA (Home Assistant OS Proxmox VM) where the Sonoff dongle still shows up under Hardware:

USB Device (usb0): host=10c4:ea60

Any suggestions?

[tteck]

I just created a new Zigbee2MQTT LXC to test

 _____   _       __             ___   __  _______  ____________
/__  /  (_)___ _/ /_  ___  ___ |__ \ /  |/  / __ \/_  __/_  __/
  / /  / / __  / __ \/ _ \/ _ \__/ // /|_/ / / / / / /   / /   
 / /__/ / /_/ / /_/ /  __/  __/ __// /  / / /_/ / / /   / /    
/____/_/\__, /_.___/\___/\___/____/_/  /_/\___\_\/_/   /_/     
       /____/ 🐝
 
Using Advanced Settings
Using Distribution: debian
Using debian Version: 12
Using Container Type: 0
Using Root Password: Automatic Login
Container ID: 110
Using Hostname: zigbee2mqtt
Using Disk Size: 4
Allocated Cores: 2
Allocated RAM: 1024
Using Bridge: vmbr0
Using IP Address: dhcp
Using Gateway IP Address: Default
Using APT-Cacher IP Address: 192.168.86.109
Disable IPv6: yes
Using Interface MTU Size: Default
Using DNS Search Domain: Host
Using DNS Server IP Address: Host
Using MAC Address: AE:1A:60:07:B7:59
Using Vlan: Default
Enable Root SSH Access: no
Enable Verbose Mode: no
Creating a Zigbee2MQTT LXC using the above advanced settings
 ✓ Using local for Template Storage.
 ✓ Using local-lvm for Container Storage.
 ✓ Updated LXC Template List
 ✓ LXC Container 110 was successfully created.
 ✓ Started LXC Container
 ✓ Set up Container OS
 ✓ Network Connected: 192.168.86.250 
 ✓ IPv4 Internet Connected
 ✓ DNS Resolved github.com to 140.82.113.4
 ✓ Updated Container OS
 ✓ Installed Dependencies
 ✓ Set up Node.js Repository
 ✓ Installed Node.js
 ✓ Set up Zigbee2MQTT Repository
Switch to Edge/dev branch? (y/N) 
 ✓ Installed Zigbee2MQTT
 ✓ Created Service
 ✓ Customized Container
 ✓ Cleaned
 ✓ Completed Successfully!

I then went straight to the console

root@zigbee2mqtt:~# ls -l /dev/serial/by-id
total 0
lrwxrwxrwx 1 root root 13 Feb  1 06:26 usb-Silicon_Labs_CP2102N_USB_to_UART_Bridge_Controller_2e893de28e93eb11842d214f3d9462e5-if00-port0 -> ../../ttyUSB0

I have no idea why yours doesn't show.
What Proxmox version are you on? I'm using 8.1.4

[navels]

I am also on 8.1.4. Just tried and again and spot-checked my log output versus yours and they are the same, still no joy.

[navels]

AHA! I had to delete the USB drive from HA (under the Hardware tab).