MAJ JK-BDxx 3.35 default BMS1

[tiji2486]

Hello,
Following the update of the BMS JK_BD2Axxx. I use: esp32-example-jkpb-rs485_0master_2slaves.yaml.
BMS0 works I receive the data, but not BMS1.
In the logs I have this error, if it can help:

[13:33:51][D][number:012]: 'rs485-bms0 cell count settings': Sending state 16.000000
[13:33:51][I][jk_rs485_bms:1239]: Balancer switch: on
[13:33:51][D][number:012]: 'rs485-bms0 short circuit protection delay': Sending state 1.500000
[13:33:51][D][number:012]: 'rs485-bms0 cell balancing starting voltage': Sending state 3.400000
[13:33:51][I][jk_rs485_bms:1310]: Precharging time from discharged: 0.000000 s
[13:33:51][D][number:012]: 'rs485-bms0 precharging time from discharge': Sending state 0.000000
[13:33:51][D][sensor:094]: 'rs485-bms0 smart sleep time': Sending state 24.00000 h with 0 decimals of accuracy
[13:33:51][D][jk_rs485_sniffer:092]: Received Event from BMS.. [address:0x00] @ 1 --> WORKING ! #####
[13:33:51][D][jk_rs485_sniffer:098]: updated last_device_settings_request_received_OK
[13:33:51][D][jk_rs485_bms:575]: This BMS address is: 1 and address received 0 ==> IDLE
[13:33:51][I][jk_rs485_sniffer:768]: REAL master is speaking to address 0x01 (request)
[13:33:51][W][component:237]: Component jk_rs485_sniffer took a long time for an operation (358 ms).
[13:33:51][W][component:238]: Components should block for at most 30 ms.
[13:33:51][D][jk_rs485_sniffer:522]: ..........................................
[13:33:51][D][jk_rs485_sniffer:501]: SILENCE: 207.000000 ms
[13:33:51][D][jk_rs485_sniffer:522]: ..........................................
[13:33:51][D][jk_rs485_sniffer:501]: SILENCE: 215.000000 ms
[13:33:51][D][jk_rs485_sniffer:522]: ..........................................
[13:33:52][D][jk_rs485_sniffer:501]: SILENCE: 217.000000 ms
[13:33:52][D][jk_rs485_sniffer:522]: ..........................................
[13:33:52][D][jk_rs485_sniffer:501]: SILENCE: 216.000000 ms
[13:33:52][D][jk_rs485_sniffer:522]: ..........................................
[13:33:52][D][jk_rs485_sniffer:797]: ###############################Sequence found SIZE: 317
### [13:33:52][W][jk_rs485_sniffer:823]: CHECKSUM failed! 0x89 != 0x00
[13:33:52][D][jk_rs485_sniffer:501]: SILENCE: 217.000000 ms
[13:33:52][D][jk_rs485_sniffer:522]: ..........................................
[13:33:52][I][jk_rs485_sniffer:768]: REAL master is speaking to address 0x09 (request)
[13:33:52][D][jk_rs485_sniffer:501]: SILENCE: 217.000000 ms

[moto501]

Glad it wasnt just me. I get the same error. Slave BMS no longer works. YOu might get the 'ocassional' data from a slave BMS, but for the most part it just reports a cheksum error.

[moto501]

Hi. Im hoping the developers can looking into this? Are we able to get an updated code?

[alex21lr]

Hi. Im hoping the developers can looking into this? Are we able to get an updated code?

@txubelaxu

[txubelaxu]

0master 2slaves yaml:
No jk-bms master
2 slaves
esp acts as master

So, to use that yaml you need to change the jk-bms adress 0x00 to 0x01 or 0x02. Both slaves different addresses: one 0x01, the other one 0x02

[tiji2486]

I don't understand, this yaml works well with 1 master and 1 exslave. Since the update, it no longer sees the slave.
However, as far as I'm concerned, I use it with Victron, and it is absolutely necessary to have a BMS in master or at address 0x00, otherwise Victron does not see the BMS.
Do you have a solution? Thank you.

[Silencer80]

Hello everyone,

I have also tried this project and operate 1 master (0x0) + 1 slave (0x1) on my Deye Hybrid.

Unfortunately, I am not getting any data from the slave either. I have the latest firmware 3.38 on the JKs.

Would be great if there could be an update.

Thank you and best regards!
-Boris

[txubelaxu]

Oh, I understand. Yes, if you want to use with Victron directly, you need to have one BMS at 0x00 (master). But… there is a better solution. That solution is I am using (I have Victron as well): txubelaxu/esphome-jk-bms code is used inside another project: https://github.com/Sleeper85/esphome-yambms This way, esp is “in the middle”: between Cerbo and BMSs. BMSs are configurated all as slaves, and ESP acts as master. This way all info can be retrieved from all of them. El El vie, 10 ene 2025 a las 9:20, tiji2486 ***@***.***> escribió:

…

I don't understand, this yaml works well with 1 master and 1 exslave. Since the update, it no longer sees the slave. However, as far as I'm concerned, I use it with Victron, and it is absolutely necessary to have a BMS in master or at address 0x00, otherwise Victron does not see the BMS. Do you have a solution? Thank you. — Reply to this email directly, view it on GitHub <#41 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BFHIJMCOPYIL57IFYMIDZMT2J57D3AVCNFSM6AAAAABTTQFABOVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCNZZGUZDMNI> . You are receiving this because you were mentioned.Message ID: ***@***.*** com>