bluetooth: controller: remove support for nRF5340 PDK

Remove support for nRF5340 PDK in the BLE controller.
The controller will now support only the nRF5340 DK.

Signed-off-by: Ioannis Glaropoulos <[email protected]>

Author: ioannisg

subsys/bluetooth/controller/Kconfig

@@ -606,7 +606,7 @@ endif # BT_CTLR
 
 config BT_CTLR_DEBUG_PINS_CPUAPP
 	bool "Bluetooth Controller Debug Pins"
-	depends on BOARD_NRF5340PDK_NRF5340_CPUAPP || BOARD_NRF5340DK_NRF5340_CPUAPP
+	depends on BOARD_NRF5340DK_NRF5340_CPUAPP
 	help
 	  Route debug GPIO toggling for the BLE Controller. Enable this when
 	  using Bluetooth Controller Debug Pins in co-processor and the main

subsys/bluetooth/controller/Kconfig.ll_sw_split

@@ -658,7 +658,7 @@ config BT_CTLR_PROFILE_ISR
 
 config BT_CTLR_DEBUG_PINS
 	bool "Bluetooth Controller Debug Pins"
-	depends on BOARD_NRF51DK_NRF51422 || BOARD_NRF52DK_NRF52832 || BOARD_NRF52DK_NRF52810 || BOARD_NRF52840DK_NRF52840 || BOARD_NRF5340PDK_NRF5340_CPUNET || BOARD_NRF5340DK_NRF5340_CPUNET || BOARD_RV32M1_VEGA
+	depends on BOARD_NRF51DK_NRF51422 || BOARD_NRF52DK_NRF52832 || BOARD_NRF52DK_NRF52810 || BOARD_NRF52840DK_NRF52840 || BOARD_NRF5340DK_NRF5340_CPUNET || BOARD_RV32M1_VEGA
 	help
 	  Turn on debug GPIO toggling for the BLE Controller. This is useful
 	  when debugging with a logic analyzer or profiling certain sections of

subsys/bluetooth/controller/ll_sw/nordic/hal/nrf5/debug.h

@@ -7,9 +7,7 @@
 
 #if defined(CONFIG_BT_CTLR_DEBUG_PINS) || \
 	defined(CONFIG_BT_CTLR_DEBUG_PINS_CPUAPP)
-#if defined(CONFIG_BOARD_NRF5340PDK_NRF5340_CPUAPP) || \
-	defined(CONFIG_BOARD_NRF5340PDK_NRF5340_CPUNET) || \
-	defined(CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP) || \
+#if defined(CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP) || \
 	defined(CONFIG_BOARD_NRF5340DK_NRF5340_CPUNET)
 #define DEBUG_PORT       NRF_P1
 #define DEBUG_PIN_IDX0   0
@@ -32,8 +30,7 @@
 #define DEBUG_PIN7       BIT(DEBUG_PIN_IDX7)
 #define DEBUG_PIN8       BIT(DEBUG_PIN_IDX8)
 #define DEBUG_PIN9       BIT(DEBUG_PIN_IDX9)
-#if defined(CONFIG_BOARD_NRF5340PDK_NRF5340_CPUAPP) || \
-	defined(CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP)
+#if defined(CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP)
 #define DEBUG_SETUP() \
 	do { \
 		DEBUG_PORT->PIN_CNF[DEBUG_PIN_IDX0] = \
@@ -67,7 +64,7 @@
 			(GPIO_PIN_CNF_MCUSEL_NetworkMCU << \
 			 GPIO_PIN_CNF_MCUSEL_Pos); \
 	} while (0)
-#endif /* CONFIG_BOARD_NRF5340PDK_NRF5340_CPUAPP */
+#endif /* CONFIG_BOARD_NRF5340DK_NRF5340_CPUAPP */
 #elif defined(CONFIG_BOARD_NRF52840DK_NRF52840)
 #define DEBUG_PORT       NRF_P1
 #define DEBUG_PIN0       BIT(1)

subsys/bluetooth/controller/ll_sw/nordic/hal/nrf5/swi.h

@@ -21,8 +21,7 @@
 #elif defined(CONFIG_SOC_SERIES_NRF53X)
 
 /* nRF53 Series Engineering D and Revision 1 IRQ mapping */
-#if defined(CONFIG_SOC_NRF5340_CPUNET) && \
-	!defined(CONFIG_BOARD_NRF5340PDK_NRF5340_CPUNET)
+#if defined(CONFIG_SOC_NRF5340_CPUNET)
 
 #define HAL_SWI_RADIO_IRQ  SWI2_IRQn
 #define HAL_SWI_WORKER_IRQ RTC0_IRQn
@@ -34,21 +33,7 @@
 #define HAL_SWI_JOB_IRQ    SWI3_IRQn
 #endif
 
-/* nRF53 Series Engineering A IRQ mapping */
-#elif defined(CONFIG_BOARD_NRF5340PDK_NRF5340_CPUNET)
-
-/* NOTE: nRF5340 Engineering A Errata [29] SWI: SWIRQ is not functional */
-#define HAL_SWI_RADIO_IRQ  EGU0_IRQn
-#define HAL_SWI_WORKER_IRQ RTC0_IRQn
-
-#if !defined(CONFIG_BT_CTLR_LOW_LAT) && \
-	(CONFIG_BT_CTLR_ULL_HIGH_PRIO == CONFIG_BT_CTLR_ULL_LOW_PRIO)
-#define HAL_SWI_JOB_IRQ    HAL_SWI_WORKER_IRQ
-#else
-#error "Use an unused IRQ line to implement a second SW IRQ."
-#endif
-
-#endif /* CONFIG_BOARD_NRF5340PDK_NRF5340_CPUNET */
+#endif /* CONFIG_SOC_NRF5340_CPUNET */
 
 #endif /* CONFIG_SOC_SERIES_NRF53X */