Unable to add any devices to zwave after 0.1.87 update

[realNotsneaky]

Hi All,

Last week zwave updated to 0.1.87. After the update, I saw 29 out of 43 sensors went unavailable and within 12 hours all Zooz sensors went unavailable. I did a rollback and still had no luck. I reset to the whole Jwave/zwave supervisor. Once everything was reset, i am still unable to add any of my sensors to the zwave. I start exclusion mode and set a zooz open-close sensor to exclusion mode (i have 4 sensors i have factory reset) nothing happens. Zwave timesouts since there was no connection. I installed js ui , did a hard reset and tried the whole process again.

The only thing from help on discord member(s) was the RSSI is low?

2023-08-28T18:49:31.142Z DRIVER all queues idle 2023-08-28T18:50:01.115Z DRIVER all queues busy 2023-08-28T18:50:01.125Z SERIAL » 0x0103003bc7 (5 bytes) 2023-08-28T18:50:01.126Z DRIVER » [REQ] [GetBackgroundRSSI] 2023-08-28T18:50:01.132Z SERIAL « [ACK] (0x06) 2023-08-28T18:50:01.134Z SERIAL « 0x0107013b9cc2c27f21 (9 bytes) 2023-08-28T18:50:01.137Z SERIAL » [ACK] (0x06) 2023-08-28T18:50:01.139Z DRIVER « [RES] [GetBackgroundRSSI] channel 0: -100 dBm channel 1: -62 dBm channel 2: -62 dBm 2023-08-28T18:50:01.143Z DRIVER all queues idle 2023-08-28T18:50:31.132Z DRIVER all queues busy 2023-08-28T18:50:31.143Z SERIAL » 0x0103003bc7 (5 bytes) 2023-08-28T18:50:31.145Z DRIVER » [REQ] [GetBackgroundRSSI] 2023-08-28T18:50:31.150Z SERIAL « [ACK] (0x06) 2023-08-28T18:50:31.152Z SERIAL « 0x0107013b9bc3c37f26 (9 bytes) 2023-08-28T18:50:31.155Z SERIAL » [ACK] (0x06) 2023-08-28T18:50:31.158Z DRIVER « [RES] [GetBackgroundRSSI] channel 0: -101 dBm channel 1: -61 dBm channel 2: -61 dBm 2023-08-28T18:50:31.166Z DRIVER all queues idle 2023-08-28T18:51:01.130Z DRIVER all queues busy 2023-08-28T18:51:01.139Z SERIAL » 0x0103003bc7 (5 bytes) 2023-08-28T18:51:01.141Z DRIVER » [REQ] [GetBackgroundRSSI] 2023-08-28T18:51:01.147Z SERIAL « [ACK] (0x06) 2023-08-28T18:51:01.150Z SERIAL « 0x0107013b9cc2c27f21 (9 bytes) 2023-08-28T18:51:01.152Z SERIAL » [ACK] (0x06) 2023-08-28T18:51:01.158Z DRIVER « [RES] [GetBackgroundRSSI] channel 0: -100 dBm channel 1: -62 dBm channel 2: -62 dBm 2023-08-28T18:51:01.166Z DRIVER all queues idle 2023-08-28T18:51:31.129Z DRIVER all queues busy 2023-08-28T18:51:31.138Z SERIAL » 0x0103003bc7 (5 bytes) 2023-08-28T18:51:31.140Z DRIVER » [REQ] [GetBackgroundRSSI] 2023-08-28T18:51:31.145Z SERIAL « [ACK] (0x06) 2023-08-28T18:51:31.149Z SERIAL « 0x0107013b9bc2c27f26 (9 bytes) 2023-08-28T18:51:31.152Z SERIAL » [ACK] (0x06) 2023-08-28T18:51:31.156Z DRIVER « [RES] [GetBackgroundRSSI] channel 0: -101 dBm channel 1: -62 dBm channel 2: -62 dBm

anyone have any ideas on what to try?

Note: I have changed out with other USB 700/800 and a new 800 GPIO chip and it's the same issue. I am at a loss now.

[robertsLando]

Cc @AlCalzone

[AlCalzone]

I think I saw something like this discussed on Discord? Essentially there was a node jamming channels 1 and 2.

[realNotsneaky]

Hi All, Sorry I forgot to update this thread. Yes, it was the Zooz Zen20 power strip that looks like it was stuck jamming the channels. ill keep an eye out to see if it does it again. Please feel free to close this ticket. Thank you!

…

On Tue, Aug 29, 2023, 5:42 AM AlCalzone ***@***.***> wrote: I think I saw something like this discussed on Discord? Essentially there was a node jamming channels 1 and 2. — Reply to this email directly, view it on GitHub <#3250 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BBSX3QIX6UG4SNGRUXX6BULXXXISTANCNFSM6AAAAAA4B4HOAM> . You are receiving this because you modified the open/close state.Message ID: ***@***.*** com>