Add PI 5 Changes.

source/docs/getting-started/installation/wiring.rst

@@ -28,7 +28,13 @@ Coprocessor without Passive POE
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 1a. Option 1: Get a micro USB (may be USB-C if using a newer Pi) to USB-A cable and plug the USB A side into a regulator like `this <https://www.amazon.com/KNACRO-Voltage-Regulator-Converter-Module/dp/B01HM12N2C/ref=sr_1_2>`_. Then, wire the regulator into your PDP/PDB and the Micro USB / USB C into your coprocessor.
 
-1b. Option 2: Use a USB power bank to power your coprocessor. Refer to this year's robot rulebook on legal implementations of this.
+.. note:: Raspberry Pi 5 may need a higher current power supply like the one in option 1b.
+
+1b. Option 2: Get a `DC regulator <https://www.amazon.com/UCTRONICS-Converter-Transformer-Voltage-Regulator/dp/B07XXWQ49N/>`_ and use two wires to the ground and 5v gpio pins on the PI.
+
+.. image:: images/gpiopinout.jpg
+
+1c. Option 3: Use a USB power bank to power your coprocessor. Refer to this year's robot rulebook on legal implementations of this.
 
 1. Run an ethernet cable from your Pi to your network switch / radio (we *STRONGLY* recommend the usage of a network switch, see the networking section for more info.)
 

source/docs/hardware/index.rst

@@ -5,6 +5,7 @@ Hardware
    :maxdepth: 2
 
    supportedhardware
+   picamerawiring
    picamconfig
    customhardware
    config

source/docs/hardware/picamconfig.rst

@@ -13,7 +13,7 @@ The GPU is not always capable of detecting other cameras automatically. The file
 Updating ``config.txt``
 -----------------------
 
-After flashing the pi image onto an SD card, open the ``boot`` segment in a file browser.
+After flashing the Pi image onto an SD card, open the ``boot`` segment in a file browser.
 
 .. note:: Windows may report "There is a problem with this drive". This should be ignored.
 
@@ -33,13 +33,17 @@ Within the file, find this block of text:
   ### IMX290/327/OV9281/Any other cameras that require additional overlays:
   ### Comment out (add a # ) to camera_auto_detect=1, and uncomment the line for
   ### the sensor you're trying to user
+  ### On devices with multiple CSI cameras like the CM4 and Pi 5 you will need to
+  ### declare which port each camera is plugged into (assuming your not using
+  ### autodetect). Remove the # before ",cam0" to define if a camera is plugged into
+  ### csi0. The config automatically assumes no port definition to be CSI1.
 
   cameraAutoDetect=1
 
-  # dtoverlay=imx290,clock-frequency=74250000
-  # dtoverlay=imx290,clock-frequency=37125000
-  # dtoverlay=imx378
-  # dtoverlay=ov9281
+  # dtoverlay=imx290,clock-frequency=74250000#,cam0
+  # dtoverlay=imx290,clock-frequency=37125000#,cam0
+  # dtoverlay=imx378#,cam0
+  # dtoverlay=ov9281#,cam0
 
   ##############################################################
 

source/docs/hardware/picamerawiring.rst

@@ -0,0 +1,27 @@
+Pi Camera Wiring
+================
+
+Background
+----------
+
+The Raspberry Pi boards feature dedicated CSI ports (1 on Pi 3 and 4, while Pi 5 and CM4 have two), which is a ribbon cable connector designed for connecting a camera module to the Raspberry Pi. This port allows users to attach a compatible camera and leverage its capabilities for various applications, such as image and video capture, computer vision projects, and more.
+
+.. warning:: Incorrect camera connection may not work or cause damage to the board or camera.
+.. warning:: Long ribbon cables are not recommended for use in FRC as they are very fragile and may be susceptible to noise.
+.. warning:: Please note which connector your Raspberry Pi has before you purchase one (they have different pin counts).
+
+Pi 3 and 4
+----------
+
+The Raspberry Pi 3 and 4 both have a single 15 pin CSI camera port.
+
+.. image:: images/pi4.png
+.. image:: images/pi4cable.png
+
+Pi 5
+----
+
+The Raspberry Pi 5 has two much smaller 22 pin CSI camera port.
+
+.. image:: images/pi5.png
+.. image:: images/pi5cable.png

source/docs/hardware/supportedhardware.rst

@@ -16,7 +16,7 @@ Pi cameras are always recommended over USB cameras as they have lower latency an
 
   * The V1 is strongly preferred over the V2 due to the V2 having undesirable FOV choices
 
-* `Innomaker OV9281 Global Shutter Camera <https://www.amazon.com/Raspberry-External-Monochrome-Bullseye-libcamera/dp/B09WTP5GZH>`_ (AprilTag Tracking)
+* `Innomaker OV9281 Global Shutter Camera <https://www.amazon.com/Raspberry-External-Monochrome-Bullseye-libcamera/dp/B09WTP5GZH>`_ (AprilTag Tracking) (Currently not supported on Pi 5)
 
 .. note:: Note that there are many CSI based OV9281 cameras but this is the only one that has been tested by the development team.
 
@@ -34,7 +34,7 @@ Pi cameras are always recommended over USB cameras as they have lower latency an
 
     The following cameras / setups are known to not work:
 
-    * Using two of the same USB cameras does not currently work because it is hard to identify the two different cameras.
+    * OV9281 on Pi 5 current does not work since tuning files dont exist from Raspberry Pi yet.
 
     * Most Logitech cameras (specifically the Logitech C270 HD Webcam (PN: 960-000694)) will not work with PhotonVision.
 
@@ -44,8 +44,8 @@ Pi cameras are always recommended over USB cameras as they have lower latency an
 
 Supported Coprocessors
 ----------------------
-* Raspberry Pi 3 / 4, with the newest variants of each being preferred (3B+ and B, respectively).
-* Raspberry Pi 4 is preferred for all forms of target tracking.
+* Raspberry Pi 4 and 5, with the newest variants of each being preferred (3B+ and B, respectively).
+* Raspberry Pi 4 is preferred for all forms of target tracking, Raspberry Pi 5 will have better preformance however has much less testing.
 * Orange Pi 4 / 5 will have better performance but will require more work to get working.
 * Mini PCs (such as Beelink N5095) have been testing and show significantly better performance than a Raspberry Pi, but require extra effort to wire to the robot / get set up. More information can be found in the set up guide `here. <https://docs.google.com/document/d/1lOSzG8iNE43cK-PgJDDzbwtf6ASyf4vbW8lQuFswxzw/edit?usp=drivesdk>`_
 * Other coprocessors can be used but may require some extra work / command line usage in order to get it working properly.
@@ -86,7 +86,7 @@ Support Levels
          * All features will work
          * Everything will be kept up to date
      -   * Gloworm
-         * Raspberry Pi 3 and Raspberry Pi 4 with the official Pi image with the Pi Cam or CSCore compatible USB Cameras
+         * Raspberry Pi 3, 4, and 5 with the official Pi image with the Pi Cam or CSCore compatible USB Cameras
    * - Compatible
      -   * No guarantee of support on Discord
          * Major features will work