BusDisplay change

Author: FoamyGuy

CircuitPython_ESP32_Camera/esp32-kaluga-onionskin-gif/code.py

@@ -54,6 +54,7 @@
 import bitmaptools
 import fourwire
 import displayio
+import busdisplay
 import sdcardio
 import storage
 import gifio
@@ -102,7 +103,7 @@ def record_pressed():
     b"\x29\x80\x78"  # Display on then delay 0x78 (120ms)
 )
 
-display = displayio.Display(display_bus, _INIT_SEQUENCE, width=320, height=240)
+display = busdisplay.BusDisplay(display_bus, _INIT_SEQUENCE, width=320, height=240)
 
 sd_spi = busio.SPI(clock=board.IO18, MOSI=board.IO14, MISO=board.IO17)
 sd_cs = board.IO12

CircuitPython_displayio/displayio_display_manual/code.py

@@ -4,6 +4,7 @@
 
 import board
 import displayio
+import busdisplay
 import fourwire
 
 # Release any previously configured displays
@@ -48,7 +49,7 @@
 )
 
 # Setup the Display
-display = displayio.Display(display_bus, INIT_SEQUENCE, width=320, height=240)
+display = busdisplay.BusDisplay(display_bus, INIT_SEQUENCE, width=320, height=240)
 
 #
 # DONE - now you can use the display however you want

CircuitPython_displayio/displayio_parallelbus/code.py

@@ -4,6 +4,7 @@
 
 import board
 import displayio
+import busdisplay
 import paralleldisplaybus
 
 # Release any previously configured displays
@@ -46,7 +47,7 @@
 )
 
 # Setup the Display
-display = displayio.Display(display_bus, INIT_SEQUENCE, width=320, height=240)
+display = busdisplay.BusDisplay(display_bus, INIT_SEQUENCE, width=320, height=240)
 
 #
 # DONE - now you can use the display however you want

OV5640_Breakout/CircuitPython_Kaluga-jpeg/code.py

@@ -25,6 +25,7 @@
 import board
 import busio
 import displayio
+import busdisplay
 import fourwire
 import espcamera
 import espidf
@@ -68,7 +69,7 @@
     b"\x29\x80\x78"  # Display on then delay 0x78 (120ms)
 )
 
-display = displayio.Display(display_bus, _INIT_SEQUENCE, width=320, height=240)
+display = busdisplay.BusDisplay(display_bus, _INIT_SEQUENCE, width=320, height=240)
 
 if espidf.get_reserved_psram() < 1047586:
     print("""Place the following line in CIRCUITPY/settings.toml, then hard-reset the board:

OV5640_Breakout/CircuitPython_Kaluga-lcd-mirror/code.py

@@ -19,6 +19,7 @@
 import busio
 import keypad
 import displayio
+import busdisplay
 import fourwire
 import espcamera
 import espidf
@@ -59,7 +60,7 @@
     b"\x29\x80\x78"  # Display on then delay 0x78 (120ms)
 )
 
-display = displayio.Display(display_bus, _INIT_SEQUENCE, width=320, height=240)
+display = busdisplay.BusDisplay(display_bus, _INIT_SEQUENCE, width=320, height=240)
 
 if espidf.get_reserved_psram() < 1047586:
     print("""Place the following line in CIRCUITPY/settings.toml, then hard-reset the board: