Add Lilygo tqt pro, with and without PSRAM

ports/espressif/boards/lilygo_tqt_pro_nopsram/board.c

@@ -0,0 +1,100 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2020 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#include "supervisor/board.h"
+#include "mpconfigboard.h"
+#include "shared-bindings/busio/SPI.h"
+#include "shared-bindings/fourwire/FourWire.h"
+#include "shared-bindings/microcontroller/Pin.h"
+#include "shared-module/displayio/__init__.h"
+#include "shared-module/displayio/mipi_constants.h"
+#include "shared-bindings/board/__init__.h"
+
+
+#define DELAY 0x80
+
+// display init sequence according to LilyGO example app
+uint8_t display_init_sequence[] = {
+    // sw reset
+    0x01, 0 | DELAY, 150,
+    // sleep out
+    0x11, 0 | DELAY, 255,
+    // normal display mode on
+    0x13, 0,
+    // display and color format settings
+    0x36, 1, 0x68,
+    0xB6, 2, 0x0A, 0x82,
+    0x3A, 1 | DELAY,  0x55, 10,
+    // ST7789V frame rate setting
+    0xB2, 5, 0x0C, 0x0C, 0x00, 0x33, 0x33,
+    // voltages: VGH / VGL
+    0xB7, 1, 0x35,
+    // ST7789V power setting
+    0xBB, 1, 0x28,
+    0xC0, 1, 0x0C,
+    0xC2, 2, 0x01, 0xFF,
+    0xC3, 1, 0x10,
+    0xC4, 1, 0x20,
+    0xC6, 1, 0x0F,
+    0xD0, 2, 0xA4, 0xA1,
+    // ST7789V gamma setting
+    0xE0, 14, 0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x32, 0x44, 0x42, 0x06, 0x0E, 0x12, 0x14, 0x17,
+    0xE1, 14, 0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x31, 0x54, 0x47, 0x0E, 0x1C, 0x17, 0x1B, 0x1E,
+    0x21, 0,
+    // display on
+    0x29, 0 | DELAY, 255,
+};
+
+
+void board_init(void) {
+    busio_spi_obj_t *spi = common_hal_board_create_spi(0);
+    fourwire_fourwire_obj_t *bus = &allocate_display_bus()->fourwire_bus;
+    bus->base.type = &fourwire_fourwire_type;
+
+    common_hal_fourwire_fourwire_construct(
+        bus,
+        spi,
+        &pin_GPIO6,    // DC
+        &pin_GPIO5,     // CS
+        &pin_GPIO1,    // RST
+        40000000,       // baudrate
+        0,              // polarity
+        0               // phase
+        );
+    busdisplay_busdisplay_obj_t *display = &allocate_display()->display;
+    display->base.type = &busdisplay_busdisplay_type;
+
+    common_hal_busdisplay_busdisplay_construct(
+        display,
+        bus,
+        128,            // width (after rotation)
+        128,            // height (after rotation)
+        1,             // column start
+        2,             // row start
+        90,              // rotation
+        16,             // color depth
+        false,          // grayscale
+        false,          // pixels in a byte share a row. Only valid for depths < 8
+        1,              // bytes per cell. Only valid for depths < 8
+        false,          // reverse_pixels_in_byte. Only valid for depths < 8
+        true,           // reverse_pixels_in_word
+        MIPI_COMMAND_SET_COLUMN_ADDRESS, // set column command
+        MIPI_COMMAND_SET_PAGE_ADDRESS,   // set row command
+        MIPI_COMMAND_WRITE_MEMORY_START, // write memory command
+        display_init_sequence,
+        sizeof(display_init_sequence),
+        &pin_GPIO10,    // backlight pin
+        NO_BRIGHTNESS_COMMAND,
+        1.0f,           // brightness
+        false,          // single_byte_bounds
+        false,          // data_as_commands
+        true,           // auto_refresh
+        60,             // native_frames_per_second
+        false,          // backlight_on_high
+        false,          // SH1107_addressing
+        50000           // backlight pwm frequency
+        );
+}

ports/espressif/boards/lilygo_tqt_pro_nopsram/mpconfigboard.h

@@ -0,0 +1,18 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2019 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#pragma once
+
+// Micropython setup
+
+#define MICROPY_HW_BOARD_NAME       "LILYGO T-QT PRO NO PSRAM"
+#define MICROPY_HW_MCU_NAME         "ESP32S3"
+
+#define CIRCUITPY_BOARD_I2C         (1)
+#define CIRCUITPY_BOARD_I2C_PIN     {{.scl = &pin_GPIO44, .sda = &pin_GPIO43}}
+
+#define CIRCUITPY_BOARD_SPI         (1)
+#define CIRCUITPY_BOARD_SPI_PIN     {{.clock = &pin_GPIO3, .mosi = &pin_GPIO2}}

ports/espressif/boards/lilygo_tqt_pro_nopsram/mpconfigboard.mk

@@ -0,0 +1,14 @@
+USB_VID = 0x303a
+USB_PID = 0x8154
+USB_PRODUCT = "T-QT PRO NO PSRAM"
+USB_MANUFACTURER = "LILYGO"
+
+IDF_TARGET = esp32s3
+
+CIRCUITPY_ESP_FLASH_MODE = qio
+CIRCUITPY_ESP_FLASH_FREQ = 80m
+CIRCUITPY_ESP_FLASH_SIZE = 8MB
+
+CIRCUITPY_ESPCAMERA = 0
+# Not enough pins.
+CIRCUITPY_PARALLELDISPLAYBUS = 0

ports/espressif/boards/lilygo_tqt_pro_nopsram/pins.c

@@ -0,0 +1,56 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2020 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#include "shared-bindings/board/__init__.h"
+#include "shared-module/displayio/__init__.h"
+
+static const mp_rom_map_elem_t board_module_globals_table[] = {
+    CIRCUITPYTHON_BOARD_DICT_STANDARD_ITEMS
+
+    // front buttons
+    { MP_ROM_QSTR(MP_QSTR_BUTTON0), MP_ROM_PTR(&pin_GPIO0) },
+    { MP_ROM_QSTR(MP_QSTR_IO0), MP_ROM_PTR(&pin_GPIO0) },
+
+    { MP_ROM_QSTR(MP_QSTR_BUTTON1), MP_ROM_PTR(&pin_GPIO47) },
+    { MP_ROM_QSTR(MP_QSTR_IO47), MP_ROM_PTR(&pin_GPIO47) },
+
+    // Left side top to bottom
+    { MP_ROM_QSTR(MP_QSTR_IO34), MP_ROM_PTR(&pin_GPIO34) },
+    { MP_ROM_QSTR(MP_QSTR_IO33), MP_ROM_PTR(&pin_GPIO33) },
+    { MP_ROM_QSTR(MP_QSTR_IO39), MP_ROM_PTR(&pin_GPIO39) },
+    { MP_ROM_QSTR(MP_QSTR_IO38), MP_ROM_PTR(&pin_GPIO38) },
+    { MP_ROM_QSTR(MP_QSTR_IO37), MP_ROM_PTR(&pin_GPIO37) },
+    { MP_ROM_QSTR(MP_QSTR_IO36), MP_ROM_PTR(&pin_GPIO36) },
+    { MP_ROM_QSTR(MP_QSTR_IO35), MP_ROM_PTR(&pin_GPIO35) },
+
+    // Right side top to bottom
+    { MP_ROM_QSTR(MP_QSTR_IO16), MP_ROM_PTR(&pin_GPIO16) },
+    { MP_ROM_QSTR(MP_QSTR_IO17), MP_ROM_PTR(&pin_GPIO17) },
+    { MP_ROM_QSTR(MP_QSTR_IO18), MP_ROM_PTR(&pin_GPIO18) },
+    { MP_ROM_QSTR(MP_QSTR_IO48), MP_ROM_PTR(&pin_GPIO48) },
+
+    // Stemma QT port
+    { MP_ROM_QSTR(MP_QSTR_IO43), MP_ROM_PTR(&pin_GPIO43) },
+    { MP_ROM_QSTR(MP_QSTR_SDA), MP_ROM_PTR(&pin_GPIO43) },
+    { MP_ROM_QSTR(MP_QSTR_IO44), MP_ROM_PTR(&pin_GPIO44) },
+    { MP_ROM_QSTR(MP_QSTR_SCL), MP_ROM_PTR(&pin_GPIO44) },
+
+    { MP_ROM_QSTR(MP_QSTR_I2C), MP_ROM_PTR(&board_i2c_obj) },
+    { MP_ROM_QSTR(MP_QSTR_STEMMA_I2C), MP_ROM_PTR(&board_i2c_obj) },
+
+    // 0.85 inch LCD GC9107
+    { MP_ROM_QSTR(MP_QSTR_LCD_BCKL), MP_ROM_PTR(&pin_GPIO10) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_DC), MP_ROM_PTR(&pin_GPIO6) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_CS), MP_ROM_PTR(&pin_GPIO5) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_CLK), MP_ROM_PTR(&pin_GPIO3) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_MOSI), MP_ROM_PTR(&pin_GPIO2) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_RST), MP_ROM_PTR(&pin_GPIO1) },
+
+    { MP_ROM_QSTR(MP_QSTR_DISPLAY), MP_ROM_PTR(&displays[0].display) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_SPI), MP_ROM_PTR(&board_spi_obj) },
+
+};
+MP_DEFINE_CONST_DICT(board_module_globals, board_module_globals_table);

ports/espressif/boards/lilygo_tqt_pro_psram/board.c

@@ -0,0 +1,100 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2020 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#include "supervisor/board.h"
+#include "mpconfigboard.h"
+#include "shared-bindings/busio/SPI.h"
+#include "shared-bindings/fourwire/FourWire.h"
+#include "shared-bindings/microcontroller/Pin.h"
+#include "shared-module/displayio/__init__.h"
+#include "shared-module/displayio/mipi_constants.h"
+#include "shared-bindings/board/__init__.h"
+
+
+#define DELAY 0x80
+
+// display init sequence according to LilyGO example app
+uint8_t display_init_sequence[] = {
+    // sw reset
+    0x01, 0 | DELAY, 150,
+    // sleep out
+    0x11, 0 | DELAY, 255,
+    // normal display mode on
+    0x13, 0,
+    // display and color format settings
+    0x36, 1, 0x68,
+    0xB6, 2, 0x0A, 0x82,
+    0x3A, 1 | DELAY,  0x55, 10,
+    // ST7789V frame rate setting
+    0xB2, 5, 0x0C, 0x0C, 0x00, 0x33, 0x33,
+    // voltages: VGH / VGL
+    0xB7, 1, 0x35,
+    // ST7789V power setting
+    0xBB, 1, 0x28,
+    0xC0, 1, 0x0C,
+    0xC2, 2, 0x01, 0xFF,
+    0xC3, 1, 0x10,
+    0xC4, 1, 0x20,
+    0xC6, 1, 0x0F,
+    0xD0, 2, 0xA4, 0xA1,
+    // ST7789V gamma setting
+    0xE0, 14, 0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x32, 0x44, 0x42, 0x06, 0x0E, 0x12, 0x14, 0x17,
+    0xE1, 14, 0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x31, 0x54, 0x47, 0x0E, 0x1C, 0x17, 0x1B, 0x1E,
+    0x21, 0,
+    // display on
+    0x29, 0 | DELAY, 255,
+};
+
+
+void board_init(void) {
+    busio_spi_obj_t *spi = common_hal_board_create_spi(0);
+    fourwire_fourwire_obj_t *bus = &allocate_display_bus()->fourwire_bus;
+    bus->base.type = &fourwire_fourwire_type;
+
+    common_hal_fourwire_fourwire_construct(
+        bus,
+        spi,
+        &pin_GPIO6,    // DC
+        &pin_GPIO5,     // CS
+        &pin_GPIO1,    // RST
+        40000000,       // baudrate
+        0,              // polarity
+        0               // phase
+        );
+    busdisplay_busdisplay_obj_t *display = &allocate_display()->display;
+    display->base.type = &busdisplay_busdisplay_type;
+
+    common_hal_busdisplay_busdisplay_construct(
+        display,
+        bus,
+        128,            // width (after rotation)
+        128,            // height (after rotation)
+        1,             // column start
+        2,             // row start
+        90,              // rotation
+        16,             // color depth
+        false,          // grayscale
+        false,          // pixels in a byte share a row. Only valid for depths < 8
+        1,              // bytes per cell. Only valid for depths < 8
+        false,          // reverse_pixels_in_byte. Only valid for depths < 8
+        true,           // reverse_pixels_in_word
+        MIPI_COMMAND_SET_COLUMN_ADDRESS, // set column command
+        MIPI_COMMAND_SET_PAGE_ADDRESS,   // set row command
+        MIPI_COMMAND_WRITE_MEMORY_START, // write memory command
+        display_init_sequence,
+        sizeof(display_init_sequence),
+        &pin_GPIO10,    // backlight pin
+        NO_BRIGHTNESS_COMMAND,
+        1.0f,           // brightness
+        false,          // single_byte_bounds
+        false,          // data_as_commands
+        true,           // auto_refresh
+        60,             // native_frames_per_second
+        false,          // backlight_on_high
+        false,          // SH1107_addressing
+        50000           // backlight pwm frequency
+        );
+}

ports/espressif/boards/lilygo_tqt_pro_psram/mpconfigboard.h

@@ -0,0 +1,18 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2019 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#pragma once
+
+// Micropython setup
+
+#define MICROPY_HW_BOARD_NAME       "LILYGO T-QT PRO PSRAM"
+#define MICROPY_HW_MCU_NAME         "ESP32S3"
+
+#define CIRCUITPY_BOARD_I2C         (1)
+#define CIRCUITPY_BOARD_I2C_PIN     {{.scl = &pin_GPIO44, .sda = &pin_GPIO43}}
+
+#define CIRCUITPY_BOARD_SPI         (1)
+#define CIRCUITPY_BOARD_SPI_PIN     {{.clock = &pin_GPIO3, .mosi = &pin_GPIO2}}

ports/espressif/boards/lilygo_tqt_pro_psram/mpconfigboard.mk

@@ -0,0 +1,18 @@
+USB_VID = 0x303a
+USB_PID = 0x8154
+USB_PRODUCT = "T-QT PRO PSRAM"
+USB_MANUFACTURER = "LILYGO"
+
+IDF_TARGET = esp32s3
+
+CIRCUITPY_ESP_FLASH_SIZE = 4MB
+CIRCUITPY_ESP_FLASH_MODE = qio
+CIRCUITPY_ESP_FLASH_FREQ = 80m
+
+CIRCUITPY_ESP_PSRAM_SIZE = 2MB
+CIRCUITPY_ESP_PSRAM_MODE = qio
+CIRCUITPY_ESP_PSRAM_FREQ = 80m
+
+CIRCUITPY_ESPCAMERA = 0
+# Not enough pins.
+CIRCUITPY_PARALLELDISPLAYBUS = 0

ports/espressif/boards/lilygo_tqt_pro_psram/pins.c

@@ -0,0 +1,56 @@
+// This file is part of the CircuitPython project: https://circuitpython.org
+//
+// SPDX-FileCopyrightText: Copyright (c) 2020 Scott Shawcroft for Adafruit Industries
+//
+// SPDX-License-Identifier: MIT
+
+#include "shared-bindings/board/__init__.h"
+#include "shared-module/displayio/__init__.h"
+
+static const mp_rom_map_elem_t board_module_globals_table[] = {
+    CIRCUITPYTHON_BOARD_DICT_STANDARD_ITEMS
+
+    // front buttons
+    { MP_ROM_QSTR(MP_QSTR_BUTTON0), MP_ROM_PTR(&pin_GPIO0) },
+    { MP_ROM_QSTR(MP_QSTR_IO0), MP_ROM_PTR(&pin_GPIO0) },
+
+    { MP_ROM_QSTR(MP_QSTR_BUTTON1), MP_ROM_PTR(&pin_GPIO47) },
+    { MP_ROM_QSTR(MP_QSTR_IO47), MP_ROM_PTR(&pin_GPIO47) },
+
+    // Left side top to bottom
+    { MP_ROM_QSTR(MP_QSTR_IO34), MP_ROM_PTR(&pin_GPIO34) },
+    { MP_ROM_QSTR(MP_QSTR_IO33), MP_ROM_PTR(&pin_GPIO33) },
+    { MP_ROM_QSTR(MP_QSTR_IO39), MP_ROM_PTR(&pin_GPIO39) },
+    { MP_ROM_QSTR(MP_QSTR_IO38), MP_ROM_PTR(&pin_GPIO38) },
+    { MP_ROM_QSTR(MP_QSTR_IO37), MP_ROM_PTR(&pin_GPIO37) },
+    { MP_ROM_QSTR(MP_QSTR_IO36), MP_ROM_PTR(&pin_GPIO36) },
+    { MP_ROM_QSTR(MP_QSTR_IO35), MP_ROM_PTR(&pin_GPIO35) },
+
+    // Right side top to bottom
+    { MP_ROM_QSTR(MP_QSTR_IO16), MP_ROM_PTR(&pin_GPIO16) },
+    { MP_ROM_QSTR(MP_QSTR_IO17), MP_ROM_PTR(&pin_GPIO17) },
+    { MP_ROM_QSTR(MP_QSTR_IO18), MP_ROM_PTR(&pin_GPIO18) },
+    { MP_ROM_QSTR(MP_QSTR_IO48), MP_ROM_PTR(&pin_GPIO48) },
+
+    // Stemma QT port
+    { MP_ROM_QSTR(MP_QSTR_IO43), MP_ROM_PTR(&pin_GPIO43) },
+    { MP_ROM_QSTR(MP_QSTR_SDA), MP_ROM_PTR(&pin_GPIO43) },
+    { MP_ROM_QSTR(MP_QSTR_IO44), MP_ROM_PTR(&pin_GPIO44) },
+    { MP_ROM_QSTR(MP_QSTR_SCL), MP_ROM_PTR(&pin_GPIO44) },
+
+    { MP_ROM_QSTR(MP_QSTR_I2C), MP_ROM_PTR(&board_i2c_obj) },
+    { MP_ROM_QSTR(MP_QSTR_STEMMA_I2C), MP_ROM_PTR(&board_i2c_obj) },
+
+    // 0.85 inch LCD GC9107
+    { MP_ROM_QSTR(MP_QSTR_LCD_BCKL), MP_ROM_PTR(&pin_GPIO10) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_DC), MP_ROM_PTR(&pin_GPIO6) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_CS), MP_ROM_PTR(&pin_GPIO5) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_CLK), MP_ROM_PTR(&pin_GPIO3) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_MOSI), MP_ROM_PTR(&pin_GPIO2) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_RST), MP_ROM_PTR(&pin_GPIO1) },
+
+    { MP_ROM_QSTR(MP_QSTR_DISPLAY), MP_ROM_PTR(&displays[0].display) },
+    { MP_ROM_QSTR(MP_QSTR_LCD_SPI), MP_ROM_PTR(&board_spi_obj) },
+
+};
+MP_DEFINE_CONST_DICT(board_module_globals, board_module_globals_table);

supervisor/shared/bluetooth/bluetooth.c

@@ -229,7 +229,7 @@ void supervisor_bluetooth_init(void) {
     }
     #endif
     while (diff < 1000) {
-        #ifdef CIRCUITPY_STATUS_LED
+        #if CIRCUITPY_STATUS_LED
         // Blink on for 50 and off for 100
         bool led_on = boot_in_discovery_mode || (diff % 150) <= 50;
         if (led_on) {