rabbit placation

Author: SupaflyFPV

presets/2025.12/rc_link/DJI_Normal.txt

@@ -62,7 +62,7 @@ set feedforward_jitter_factor = 7
     set feedforward_averaging = 2_POINT
     set feedforward_smooth_factor = 40
     set feedforward_jitter_factor = 15
-    set rc_smoothing_auto_factor = 250  
+    set rc_smoothing_auto_factor = 250
     set rc_smoothing_auto_factor_throttle = 170
     set rc_smoothing_setpoint_cutoff = 12
     set rc_smoothing_throttle_cutoff = 20

presets/2025.12/rc_link/elrs_250hz.txt

@@ -33,7 +33,7 @@ set feedforward_jitter_factor = 6
         set feedforward_smooth_factor = 45
         set feedforward_jitter_factor = 10
         set rc_smoothing_auto_factor = 140
-s       et rc_smoothing_setpoint_cutoff = 25
+        set rc_smoothing_setpoint_cutoff = 25
     #$ OPTION END
     #$ OPTION BEGIN (UNCHECKED): Cinematic
         set feedforward_smooth_factor = 60

presets/2025.12/rc_link/elrs_50hz.txt

@@ -64,7 +64,7 @@ set feedforward_boost = 5
     #$ OPTION BEGIN (UNCHECKED): Single Cell values
         set report_cell_voltage = ON
     #$ OPTION END
-#   $ OPTION BEGIN (UNCHECKED): Whole pack values
+    #$ OPTION BEGIN (UNCHECKED): Whole pack values
         set report_cell_voltage = OFF
     #$ OPTION END
 #$ OPTION_GROUP END

presets/2025.12/rc_link/frsky_sbus_fport.txt

@@ -5,7 +5,7 @@
 #$ KEYWORDS: frsky, sbus, fport, 9ms, 111hz, rc, link, smoothing
 #$ AUTHOR: ctzsnooze
 #$ DESCRIPTION: RC link settings for a 111Hz / 9ms D16 with FrSky Sbus or FPort link.
-#$ DESCRIPTION: WARNING: make ABSOLUTELY SURE that the OpenTx or EdgeTx Hardware ADC Filter is un-checked!
+#$ DESCRIPTION: WARNING: make sure that the OpenTx or EdgeTx Hardware ADC Filter is un-checked!
 #$ DESCRIPTION: Use a recent version of OpenTx / EdgeTx with good module sync.
 #$ DESCRIPTION: Note: Telemetry requires smartPort (s.Port) and does not convey RSSI (use Lua or analog RSSI).
 #$ FORCE_OPTIONS_REVIEW: TRUE
@@ -69,7 +69,7 @@ set tlm_halfduplex = ON
 
 #$ OPTION_GROUP BEGIN: (EXCLUSIVE) Voltage readings (choose one):
     #$ OPTION BEGIN (UNCHECKED): Single Cell values
-    set report_cell_voltage = ON
+        set report_cell_voltage = ON
     #$ OPTION END
     #$ OPTION BEGIN (UNCHECKED): Whole pack values
         set report_cell_voltage = OFF
@@ -89,7 +89,7 @@ set tlm_halfduplex = ON
     #$ OPTION BEGIN (UNCHECKED): Telemetry inverted (default is not inverted)
         set tlm_inverted = ON
     #$ OPTION END
-    #$ OPTION BEGIN (UNCHECKED): Full duplex telemetry (default is helf duplex)
+    #$ OPTION BEGIN (UNCHECKED): Full duplex telemetry (default is half duplex)
         set tlm_halfduplex = OFF
     #$ OPTION END
     #$ OPTION BEGIN (UNCHECKED): Bound with >8 channels (not recommended)

presets/2025.12/rc_link/generic/1000hz_race.txt

@@ -5,7 +5,7 @@
 #$ KEYWORDS: 1000Hz, 1ms, rc, rx, link, smoothing, ELRS
 #$ AUTHOR: Sugar K
 #$ DESCRIPTION: Generic RC link settings for racing with 1000Hz RC link. Best used with 2025.12.
-#$ DESCRIPTION: WARNING: make ABSOLUTELY SURE that the OpenTx or EdgeTx Hardware ADC Filter is un-checked!
+#$ DESCRIPTION: WARNING: make sure that the OpenTx or EdgeTx Hardware ADC Filter is un-checked!
 #$ DESCRIPTION: WARNING: check that you are using a compatible version of EdgeTx or OpenTx!
 
 #$ PRIORITY: 0