8.3 Error Message

The error returned from BNP will pass to the callback as an error object. The error message is a string formatted as

    HciError(10): Synch conn limit exceeded

, where 'HciError' denotes the type of error and number 10 is the corresponding error code.

******************************************** ### 8.3.1 HciError

Error code	Description
1	Unknown hci cmd
2	Unknown conn id
3	Hw failure
4	Page timeout
5	Auth failure
6	Pin key missing
7	Mem cap exceeded
8	Conn timeout
9	Conn limit exceeded
10	Synch conn limit exceeded
11	Acl conn already exists
12	Cmd disallowed
13	Conn rej limited resources
14	Conn rejected security reasons
15	Conn rejected unacceptable bdaddr
16	Conn accept timeout exceeded
17	Unsupported feature param value
18	Invalid hci cmd params
19	Remote user term conn
20	Remote device term conn low resources
21	Remote device term conn power off
22	Conn term by local host
23	Repeated attempts
24	Pairing not allowed
25	Unknown lmp pdu
26	Unsupported remote feature
27	Sco offset rej
28	Sco interval rej
29	Sco air mode rej
30	Invalid lmp params
31	Unspecified error
32	Unsupported lmp param val
33	Role change not allowed
34	Lmp ll resp timeout
35	Lmp err transaction collision
36	Lmp pdu not allowed
37	Encrypt mode not acceptable
38	Link key can not be changed
39	Req qos not supported
40	Instant passed
41	Pairing with unit key not supported
42	Different transaction collision
43	Reserved 1
44	Qos unacceptable param
45	Qos rej
46	Chan assessment not supported
47	Insufficient security
48	Param out of mandatory range
49	Reserved 2
50	Role switch pending
51	Reserved 3
52	Reserved slot violation
53	Role switch failed
54	Extended inquiry resp too large
55	Simple pairing not supported by host
56	Host busy pairing
57	Conn rej no suitable chan found
58	Controller busy
59	Unacceptable conn interval
60	Directed adv timeout
61	Conn term mic failure
62	Conn failed to establish
63	Mac conn failed

******************************************** ### 8.3.2 AttError

Error code	Description
1	The attribute handle given was not valid on this server
2	The attribute cannot be read
3	The attribute cannot be written
4	The attribute PDU was invalid
5	The attribute requires authentication before it can be read or written
6	Attribute server does not support the request received from the client
7	Offset specified was past the end of the attribute
8	The attribute requires authorization before it can be read or written
9	Too many prepare writes have been queued
10	No attribute found within the given attribute handle range
11	The attribute cannot be read or written using the Read Blob Request
12	The Encryption Key Size used for encrypting this link is insufficient
13	The attribute value length is invalid for the operation
14	The attribute request that was requested has encountered an error that was unlikely
15	The attribute requires encryption before it can be read or written
16	The attribute type is not a supported grouping attribute as defined by a higher layer specification
17	Insufficient Resources to complete the request
128	The attribute value is invalid for the operation

******************************************** ### 8.3.3 GenericError

Error code	Description
1	Failure
2	Invalidparameter
3	Invalid task
4	Msg buffer not avail
5	Invalid msg pointer
6	Invalid event id
7	Invalid interrupt id
8	No timer avail
9	Nv item uninit
10	Nv oper failed
11	Invalid mem size
12	Nv bad item len
16	Ble Not Ready
17	Ble Already In Requested Mode
18	Ble Incorrect Mode
19	Ble MemAlloc Error
20	Ble Not Connected
21	Ble No Resources
22	Ble Pending
23	Ble Timeout
24	Ble Invalid Range
25	Ble Link Encrypted
26	Ble Procedure Complete
48	Ble GAP User Canceled
49	Ble GAP Conn Not Acceptable
50	Ble GAP Bond Rejected
64	Ble Invalid PDU
65	Ble Insufficient Authen
66	Ble Insufficient Encrypt
67	Ble Insufficient KeySize

******************************************** ### 8.3.4 Reason Code of Link-termination

Value	Description
8	Supervisor Timeout
19	Peer Requested
22	Host Requested
34	Control Packet Timeout
40	Control Packet Instant Passed
59	LSTO Violation
61	MIC Failure