[MWAN] Clarified setting Connector with static IPs

src/content/docs/magic-wan/configuration/connector/configure-hardware-connector/index.mdx

@@ -8,12 +8,6 @@ sidebar:
 
 import { GlossaryTooltip, Render, Card } from "~/components";
 
-## Before you begin
-
-<Render file="connector/before-you-begin" />
-
----
-
 ## Prerequisites
 
 You need to purchase [Magic WAN](https://www.cloudflare.com/magic-wan/) before you can purchase and use the Magic WAN Connector. The Magic WAN Connector can function as your primary edge device for your network, or be deployed in-line with existing network gear.
@@ -24,6 +18,21 @@ Contact your account representative to learn more about purchasing options for t
 
 ---
 
+## Before you begin
+
+<Render file="connector/before-you-begin" />
+
+---
+
+## DHCP vs static IP connections
+
+Magic WAN Connector uses a DHCP connection at first boot to download your settings and go through the activation process. If you need to use a static IP in your Connector, however, and this is a fresh install:
+1. Connect Magic WAN Connector to a DHCP port with access to the Internet
+2. Go through the [setup flow](#set-up-cloudflare-dashboard) below and activate your Connector
+3. Refer to [WAN with a static IP address](#wan-with-a-static-ip-address)
+
+---
+
 ## Port speeds
 
 The hardware version of the Magic WAN connector includes two [SFP+ ports](https://en.wikipedia.org/wiki/Small_Form-factor_Pluggable) that support 10G throughput, as well as six RJ45 ports that support 1G throughput.
@@ -113,16 +122,27 @@ If there is a firewall deployed upstream of the Magic WAN Connector, configure t
 	}}
 />
 
-### WAN with a static IP address
-
-After activating your Connector, you can use it in a network configuration with the WAN interface set to a static IP address - that is, an Internet configuration that is not automatically set by DHCP.
-
-To use your Connector on a network configuration with a static IP:
+---
 
-1. Wait 60 seconds after activating your Connector.
-2. Unplug the physical connection to the Internet-connected device which provides DHCP.
-3. Adjust your physical connections as required to match the static configuration, and make changes to the [WAN settings](#2-create-a-wan) in the Cloudflare dashboard to reflect the static IP address configuration.
-4. Power cycle the Connector.
+## WAN with a static IP address
+
+After activating your Connector, you can use it in a network configuration with the WAN interface set to a static IP address — that is, an Internet configuration that is not automatically set by DHCP. To use your Connector on a network configuration with a static IP follow the steps below.
+
+:::caution
+Before proceeding, make sure that you went through the setup workflow and activated your Magic WAN Connector.
+:::
+
+1. Connect Magic WAN Connector to a DHCP port with access to the Internet.
+2. [Create a site](#1-create-a-site) in the Cloudflare dashboard.
+3. Associate a Connector to it.
+4. Create a [DHCP WAN](#2-create-a-wan).
+5. [Active](#activate-connector) and power on your Connector.
+6. Wait 60 seconds.
+7. Make changes to the [WAN settings](#2-create-a-wan) in the Cloudflare dashboard to a static IP set up.
+8. Wait 60 seconds again.
+9. Magic WAN Connector will go offline. This is normal and expected behavior.
+10. Adjust your physical connections as required to match the static configuration.
+11. Magic WAN Connector comes back online.
 
 ---
 

src/content/docs/magic-wan/configuration/connector/configure-virtual-connector.mdx

@@ -9,10 +9,6 @@ import { Render } from "~/components";
 
 Virtual Magic WAN Connector (Virtual Connector) is a virtual appliance alternative to the hardware based Magic WAN Connector appliance. These two versions of Connector are identical otherwise.
 
-## Before you begin
-
-<Render file="connector/before-you-begin" />
-
 ## Prerequisites
 
 Before you can install Virtual Connector, you need an Enterprise account with Magic WAN enabled. Additionally, you need to have a VMware host with sufficient compute, memory, and storage to run the virtual machine with Virtual Connector. This includes:
@@ -27,6 +23,21 @@ Before you can install Virtual Connector, you need an Enterprise account with Ma
 
 Refer to [VMware's documentation](https://docs.vmware.com/en/VMware-vSphere/7.0/com.vmware.esxi.install.doc/GUID-B2F01BF5-078A-4C7E-B505-5DFFED0B8C38.html) for more information on how to install ESXi and configure a virtual machine.
 
+---
+
+## Before you begin
+
+<Render file="connector/before-you-begin" />
+
+---
+
+## DHCP vs static IP connections
+
+Virtual Connector uses a DHCP connection at first boot to download your settings and go through the activation process. If you need to use a static IP in your Virtual Connector, however, and this is a fresh install:
+1. Connect the machine with your Virtual Connector VM to a DHCP port with access to the Internet
+2. Go through the [setup flow](#set-up-cloudflare-dashboard) below and activate your Connector
+3. Refer to [WAN with a static IP address](#wan-with-a-static-ip-address)
+
 ## Obtain the Virtual Connector image
 
 Contact your account team at Cloudflare to obtain the Virtual Connector [OVA package](https://docs.vmware.com/en/VMware-vSphere/7.0/com.vmware.vsphere.vm_admin.doc/GUID-AE61948B-C2EE-436E-BAFB-3C7209088552.html) and license keys. The OVA image includes the files required to install and configure the virtual machine (VM) for Virtual Connector with the appropriate settings.
@@ -40,9 +51,9 @@ You will consume one license key for each instance created. For example, if you
 The following instructions assume you already have VMware ESXi hypervisor installed with sufficient resources. Refer to [Prerequisites](#prerequisites) for more information.
 
 1. When setting up your VMware ESXi, you need to create port groups for Virtual Connector. Go to **Networking** > **Port groups**, and prepare your vSwitch port groups and/or VLANs for your desired network topology. For example, a simple deployment typically has:
-   - A WAN port group where the Virtual Connector will get an IP address (static or DHCP) that has access to the Internet.
-   - A LAN port group, where the Virtual Connector will act as default router, and possibly DHCP server.
-   - A null, or unused, port group for allocating unused virtual interfaces in the Virtual Connector. You can, for example, create a null port group with the name of `Null port group`, and a **VLAN ID** of `999`.
+	- A WAN port group where the Virtual Connector will get an IP address (static or DHCP) that has access to the Internet.
+	- A LAN port group, where the Virtual Connector will act as default router, and possibly DHCP server.
+	- A null, or unused, port group for allocating unused virtual interfaces in the Virtual Connector. You can, for example, create a null port group with the name of `Null port group`, and a **VLAN ID** of `999`.
 
 :::note[VLAN tagging]
 Virtual Connector supports creating subinterfaces through the use of [802.1Q VLAN tagging](https://en.wikipedia.org/wiki/IEEE_802.1Q).
@@ -59,38 +70,29 @@ Refer to [VMWare's documentation](https://kb.vmware.com/s/article/1003825) for m
 
 2. Extract the files in the OVA image provided by your Cloudflare account team. For example:
 
-   ```txt
-   tar -xvf mconn-2024-1-3.ova
-   ```
+	```txt
+	tar -xvf mconn-2024-1-3.ova
+	```
 
-   Take note of the folder where you are extracting the files to, as you will need to refer to that folder when creating the VM.
+	Take note of the folder where you are extracting the files to, as you will need to refer to that folder when creating the VM.
 
 3. Go to **Virtual Machines** > **Create/Register VM** wizard to start deploying the Virtual Connector.
-
 4. Select **Deploy a virtual machine from an OVF or OVA file** > **Next**.
-
 5. Choose a descriptive name for your virtual machine.
-
 6. Upload the files you have extracted from the OVA image. These include `mconn.ovf`, `mconn.nvram`, and `mconn.vmdk`.
-
 7. Select where you want to save the files extracted from the OVA image > **Next**.
-
 8. In **Networking mappings**, select assignments for your desired topology according to the port groups you set up previously:
-
-   1. For example, map `eno1` port to `VM Network` to create your WAN, and `eno2` to `LAN0` to act as your LAN port.
-   2. Allocate any unused ports to the `null` port group.
-   3. Take note of your configuration. You will need this information to configure your network in the Cloudflare dashboard.
-
+	1. For example, map `eno1` port to `VM Network` to create your WAN, and `eno2` to `LAN0` to act as your LAN port.
+	2. Allocate any unused ports to the `null` port group.
+	3. Take note of your configuration. You will need this information to configure your network in the Cloudflare dashboard.
 9. In **Disk provisioning**, select **Thin**.
-
 10. Before completing the deployment wizard, disable **Power on automatically**. This is important so that you can configure the license key prior to boot.
-
 11. Configure the virtual machine with the license key your account team provided you:
-    1. Select the Virtual Connector's VM > **Settings**.
-    2. Go to **VM Options** > **Advanced** > **Edit Configuration**.
-    3. Select **Add parameter** to add your license key. Scroll down to the last entry (this is where VMware adds the new parameter), and add the following two new entries:
-       - **Key**: `guestinfo.cloudflare.identity`
-       - **Value**: `<YOUR_LICENCE_KEY>`
+	1. Select the Virtual Connector's VM > **Settings**.
+	2. Go to **VM Options** > **Advanced** > **Edit Configuration**.
+	3. Select **Add parameter** to add your license key. Scroll down to the last entry (this is where VMware adds the new parameter), and add the following two new entries:
+		- **Key**: `guestinfo.cloudflare.identity`
+		- **Value**: `<YOUR_LICENCE_KEY>`
 
 :::note
 You cannot use the same license key twice, or reuse a key once the virtual machine has been registered with Cloudflare. You need a new key from your account team for every new Virtual Connector.
@@ -121,17 +123,6 @@ You cannot use the same license key twice, or reuse a key once the virtual machi
 	}}
 />
 
-### WAN with a static IP address
-
-After activating your Virtual Connector, you can use it in a network configuration with the WAN interface set to a static IP address - that is, an Internet configuration that is not automatically set by DHCP.
-
-To use your Virtual Connector on a network configuration with a static IP:
-
-1. Wait 60 seconds after activating your Connector.
-2. Modify your Port Groups as needed to change the source from which the WAN port obtains its IP address.
-3. [Adjust the WAN settings](#2-create-a-wan) in the Cloudflare dashboard to reflect the new static IP address configuration.
-4. Reboot your virtual machine.
-
 ## Boot your Virtual Connector
 
 1. Go to **Virtual Machines** in VMware, and boot up Virtual Connector's VM.
@@ -142,6 +133,27 @@ To use your Virtual Connector on a network configuration with a static IP:
 
 ---
 
+## WAN with a static IP address
+
+After activating your Virtual Connector, you can use it in a network configuration with the WAN interface set to a static IP address - that is, an Internet configuration that is not automatically set by DHCP. To use your Virtual Connector on a network configuration with a static IP follow the steps below.
+
+:::caution
+Before proceeding, make sure that you went through the setup workflow and activated your Virtual Connector.
+:::
+
+1. Connect the machine where you installed the VM with Virtual Connector to a DHCP port with access to the Internet.
+2. [Create a site](#1-create-a-site) in the Cloudflare dashboard.
+3. Associate a Connector to it.
+4. Create a [DHCP WAN](#2-create-a-wan).
+5. [Active](#activate-connector) and boot your Virtual Connector.
+6. Wait 60 seconds.
+7. Make changes to the [WAN settings](#2-create-a-wan) in the Cloudflare dashboard to a static IP set up.
+8. Wait 60 seconds again.
+9. Modify your [Port Groups](#deploy-the-virtual-connector-on-vmware) as needed to change the source from which the WAN port obtains its IP address.
+10. Reboot your virtual machine.
+
+---
+
 <Render
 	file="connector/ha-configs"
 	params={{

src/content/partials/magic-wan/connector/create-site.mdx

@@ -77,7 +77,9 @@ Take note of the site `id` parameter, as you will need it to create WANs and LAN
 3. **Interface number** <Markdown text={props.wan} />
 4. In **VLAN ID**, enter a number between `0` and `4094` to specify a [VLAN ID](/magic-wan/configuration/connector/reference/#vlan-id).
 5. In **Priority**, choose the priority for your WAN. Lower numbers have higher priority. Refer to <GlossaryTooltip term="traffic steering" link="/magic-wan/reference/traffic-steering/">Traffic steering</GlossaryTooltip> to learn more about how Cloudflare calculates priorities.
-6. **Addressing**: If this is the first time you are setting up your Magic WAN Connector, select **DHCP**. After you activate your Connector, you can then choose to continue fetching the WAN IP address from a DHCP server, or change it to a static IP. If you choose a static IP, you also need to specify the static IP and gateway addresses.
+6. **Addressing**: Select **DHCP**. This is needed the first time you set up your Connector to successfully download all settings to the machine and activate it. If you need a static IP address in your network environment:
+	1. Continue the set up flow below to activate your Connector
+	2. Refer to [WAN with a static IP address](#wan-with-a-static-ip-address). If you choose a static IP, you also need to specify the static IP and gateway addresses.
 
   <div class="medium-img">
 
@@ -117,30 +119,18 @@ curl https://api.cloudflare.com/client/v4/accounts/{account_id}/magic/sites/{sit
 <Tabs syncKey="dashPlusAPI"> <TabItem label="Dashboard">
 
 1. In **LAN configuration**, select **Create**.
-
 2. Enter a descriptive name for your LAN in **Interface name**.
-
 3. **Interface number** <Markdown text={props.lan} />
-
 4. In **VLAN ID**, specify a [VLAN ID](/magic-wan/configuration/connector/reference/#vlan-id) to create virtual LANs.
-
 5. In **Static addressing** > **Static address** give your Connector's LAN interface its IP address. You can also enable the following options if they suit your use case:
-
    - **This is a DHCP server**: If your Connector is a [DHCP server](/magic-wan/configuration/connector/network-options/dhcp/dhcp-server/).
    - **This is a DHCP relay**: If your Connector is a [DHCP relay](/magic-wan/configuration/connector/network-options/dhcp/dhcp-relay/).
-
 6. (Optional) In **Directly attached subnet** > **Static NAT prefix**, enter a CIDR prefix to enable NAT (network address translation). The prefix you enter here should be the same size as the prefix entered in **Static addressing**. For example, both networks have a subnet mask of `/24`: `192.168.100.0/24` and `10.10.100.0/24`.
-
 7. (Optional) If your LAN contains additional subnets behind a layer 3 router, select **Add routed subnet** under **Routed subnets** to add them:
-
    - **Prefix**: The CIDR prefix for the subnet behind the L3 router.
    - **Next hop**: The address of the L3 router to which the Connector should forward packets for this subnet.
-   - **Static NAT prefix**: Optional setting. If you want to enable NAT for a routed subnet, supply an "external" prefix for the overlay-facing side of the NAT to use. It must be the same size as **Prefix**.
-
-     Refer to [Routed subnets](/magic-wan/configuration/connector/network-options/routed-subnets/) for more information.
-
+   - **Static NAT prefix**: Optional setting. If you want to enable NAT for a routed subnet, supply an "external" prefix for the overlay-facing side of the NAT to use. It must be the same size as **Prefix**. <br /> Refer to [Routed subnets](/magic-wan/configuration/connector/network-options/routed-subnets/) for more information.
 8. Select **Save**.
-
 9. Select **Save and exit** to finish your configuration. Tunnels and <GlossaryTooltip term="static route">static routes</GlossaryTooltip> will be automatically created and associated with your site once the Magic WAN Connector boots up (refer to the next step).
 
 </TabItem> <TabItem label="API">