Skip to content

Actions: espressif/esp-usb

Actions

Bot response to issues

Actions

Loading...
Loading

Show workflow options

Create status badge

Loading
issue_bot.yml
47 workflow runs
47 workflow runs

Filter by Event

Filter by Status

Filter by Branch

Filter by Actor

cdc_acm_host_open Memory allocation failure policy Bot response to issues #47: Issue #444 edited by jhleesyszone-ux
38s
38s
cdc_acm_host_open Memory allocation failure policy Bot response to issues #46: Issue #444 edited by jhleesyszone-ux
51s
51s
cdc_acm_host_open Memory allocation failure policy Bot response to issues #45: Issue #444 edited by jhleesyszone-ux
43s
43s
cdc_acm_host_open Memory allocation failure policy Bot response to issues #44: Issue #444 opened by jhleesyszone-ux
35s
35s
ESP32-S3 | The component 'esp_hal_usb' could not be found. | NOTICE: espressif__usb overrides usb since "project_managed_components" type got higher priority than "idf_components" (IEC-492) Bot response to issues #43: Issue #425 opened by itismejy
8m 14s
8m 14s
tinyusb_msc: heap_caps_aligned_calloc() allocates 4x needed memory (DMA OOM) (IEC-486) Bot response to issues #42: Issue #397 opened by pztrick
27s
27s
esp_modem_usb_dte on ESP32-P4: how to properly initialize FS PHY2 (IEC-485) Bot response to issues #41: Issue #396 opened by dmartauz
59s
59s
OV5647+UVC摄像头 (IEC-475) Bot response to issues #40: Issue #376 opened by Whatever910
40s
40s
RX buffer append supported for ESP32-P4 (IEC-474) Bot response to issues #39: Issue #374 opened by AlexandarMilissov
43s
43s
ESP32C5 support on Esp-IDF 6.0-beta1 (IEC-472) Bot response to issues #38: Issue #371 opened by OyczE
31s
31s
Create two USB MSC using different partitions, with access to only one partition (IEC-468) Bot response to issues #37: Issue #362 edited by PR2403
29s
29s
Create two USB MSC using different partitions, with access to only one partition (IEC-468) Bot response to issues #36: Issue #362 opened by PR2403
47s
47s
FTDI Driver doesn't report state change on any modem signals from FTDI chip (IEC-461) Bot response to issues #35: Issue #361 opened by Rotario
33s
33s
FTDI VCP Driver to include CTS signal on change? (IEC-460) Bot response to issues #34: Issue #360 opened by Rotario
40s
40s
HID设置端点5及端点6失效 (IEC-452) Bot response to issues #33: Issue #349 opened by qunkejiang
39s
39s
2.0: Device not responding to setup address (IEC-447) Bot response to issues #32: Issue #342 opened by clackups
35s
35s
tud_msc_write10_cb and other msc function is no longer weak (IEC-426) Bot response to issues #31: Issue #330 opened by qwx
31s
31s
OUT direction ZLP causes corrupt transfer if DMA disabled (IEC-414) Bot response to issues #30: Issue #315 opened by projectgus
38s
38s
Missing USB HOST CDC VID/PID found on ESP32-C3 development board (IEC-404) Bot response to issues #29: Issue #302 edited by LucienMP
3m 8s
3m 8s
Missing USB HOST CDC VID/PID found on ESP32-C3 development board (IEC-404) Bot response to issues #28: Issue #302 opened by LucienMP
41s
41s
[vfs_tinyusb] static struct cause register twice missing the first (IEC-397) Bot response to issues #27: Issue #285 opened by kaidegit
1m 6s
1m 6s
Tinyusb v2.0.0 USB CDC not receiving data (IEC-396) Bot response to issues #26: Issue #283 opened by Rotario
32s
32s
Update hid.h from master repository (IEC-395) Bot response to issues #25: Issue #280 opened by filimonic
35s
35s
uvc_host not support high speed on esp32p4? (IEC-394) Bot response to issues #24: Issue #279 edited by Dandjinh
1m 0s
1m 0s
uvc_host not support high speed on esp32p4? (IEC-394) Bot response to issues #23: Issue #279 opened by Dandjinh
1m 1s
1m 1s