Add board file for Pimoroni Pico Plus 2 W

src/boards/include/boards/pimoroni_pico_plus2_w_rp2350.h

@@ -0,0 +1,137 @@
+/*
+ * Copyright (c) 2020 Raspberry Pi (Trading) Ltd.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+// -----------------------------------------------------
+// NOTE: THIS HEADER IS ALSO INCLUDED BY ASSEMBLER SO
+//       SHOULD ONLY CONSIST OF PREPROCESSOR DIRECTIVES
+// -----------------------------------------------------
+
+// This header may be included by other board headers as "boards/pimoroni_pico_plus2_w_rp2350.h"
+
+// pico_cmake_set PICO_PLATFORM=rp2350
+// pico_cmake_set PICO_CYW43_SUPPORTED = 1
+
+#ifndef _BOARDS_PIMORONI_PICO_PLUS2_W_RP2350_H
+#define _BOARDS_PIMORONI_PICO_PLUS2_W_RP2350_H
+
+// For board detection
+#define PIMORONI_PICO_PLUS2_W_RP2350
+
+// --- BOARD SPECIFIC ---
+#define SPICE_SPI 0
+#define SPICE_TX_MISO_PIN 32
+#define SPICE_RX_CS_PIN 33
+#define SPICE_NETLIGHT_SCK_PIN 34
+#define SPICE_RESET_MOSI_PIN 35
+#define SPICE_PWRKEY_BL_PIN 36
+
+#define PIMORONI_PICO_PLUS2_USER_SW_PIN 45
+#define PIMORONI_PICO_PLUS2_PSRAM_CS_PIN 47
+
+// --- UART ---
+#ifndef PICO_DEFAULT_UART
+#define PICO_DEFAULT_UART 0
+#endif
+#ifndef PICO_DEFAULT_UART_TX_PIN
+#define PICO_DEFAULT_UART_TX_PIN 0
+#endif
+#ifndef PICO_DEFAULT_UART_RX_PIN
+#define PICO_DEFAULT_UART_RX_PIN 1
+#endif
+
+// --- LED ---
+// no PICO_DEFAULT_LED_PIN - LED is on Wireless chip
+// no PICO_DEFAULT_WS2812_PIN
+
+// --- I2C ---
+#ifndef PICO_DEFAULT_I2C
+#define PICO_DEFAULT_I2C 0
+#endif
+#ifndef PICO_DEFAULT_I2C_SDA_PIN
+#define PICO_DEFAULT_I2C_SDA_PIN 4
+#endif
+#ifndef PICO_DEFAULT_I2C_SCL_PIN
+#define PICO_DEFAULT_I2C_SCL_PIN 5
+#endif
+
+// --- SPI ---
+#ifndef PICO_DEFAULT_SPI
+#define PICO_DEFAULT_SPI 0
+#endif
+#ifndef PICO_DEFAULT_SPI_SCK_PIN
+#define PICO_DEFAULT_SPI_SCK_PIN SPICE_NETLIGHT_SCK_PIN
+#endif
+#ifndef PICO_DEFAULT_SPI_TX_PIN
+#define PICO_DEFAULT_SPI_TX_PIN SPICE_RESET_MOSI_PIN
+#endif
+#ifndef PICO_DEFAULT_SPI_RX_PIN
+#define PICO_DEFAULT_SPI_RX_PIN SPICE_TX_MISO_PIN
+#endif
+#ifndef PICO_DEFAULT_SPI_CSN_PIN
+#define PICO_DEFAULT_SPI_CSN_PIN SPICE_RX_CS_PIN
+#endif
+
+// --- FLASH ---
+
+#define PICO_BOOT_STAGE2_CHOOSE_W25Q080 1
+
+#ifndef PICO_FLASH_SPI_CLKDIV
+#define PICO_FLASH_SPI_CLKDIV 2
+#endif
+
+// pico_cmake_set_default PICO_FLASH_SIZE_BYTES = (16 * 1024 * 1024)
+#ifndef PICO_FLASH_SIZE_BYTES
+#define PICO_FLASH_SIZE_BYTES (16 * 1024 * 1024)
+#endif
+
+// The GPIO Pin used to read VBUS to determine if the device is battery powered.
+#ifndef PICO_VBUS_PIN
+#define PICO_VBUS_PIN 24
+#endif
+
+// The GPIO Pin used to monitor VSYS. Typically you would use this with ADC.
+// There is an example in adc/read_vsys in pico-examples.
+#ifndef PICO_VSYS_PIN
+#define PICO_VSYS_PIN 43
+#endif
+
+#ifndef PICO_RP2350_A2_SUPPORTED
+#define PICO_RP2350_A2_SUPPORTED 1
+#endif
+
+// --- CYW43 ---
+
+#ifndef CYW43_PIN_WL_HOST_WAKE
+#define CYW43_PIN_WL_HOST_WAKE 24
+#endif
+
+#ifndef CYW43_PIN_WL_REG_ON
+#define CYW43_PIN_WL_REG_ON 23
+#endif
+
+#ifndef CYW43_WL_GPIO_COUNT
+#define CYW43_WL_GPIO_COUNT 3
+#endif
+
+#ifndef CYW43_WL_GPIO_LED_PIN
+#define CYW43_WL_GPIO_LED_PIN 0
+#endif
+
+// If CYW43_WL_GPIO_VBUS_PIN is defined then a CYW43 GPIO has to be used to read VBUS.
+// This can be passed to cyw43_arch_gpio_get to determine if the device is battery powered.
+// PICO_VBUS_PIN and CYW43_WL_GPIO_VBUS_PIN should not both be defined.
+#ifndef CYW43_WL_GPIO_VBUS_PIN
+#define CYW43_WL_GPIO_VBUS_PIN 2
+#endif
+
+// If CYW43_USES_VSYS_PIN is defined then CYW43 uses the VSYS GPIO (defined by PICO_VSYS_PIN) for other purposes.
+// If this is the case, to use the VSYS GPIO it's necessary to ensure CYW43 is not using it.
+// This can be achieved by wrapping the use of the VSYS GPIO in cyw43_thread_enter / cyw43_thread_exit.
+#ifndef CYW43_USES_VSYS_PIN
+#define CYW43_USES_VSYS_PIN 1
+#endif
+
+#endif