Alignment to nrfx_timer rework

drivers/serial/Kconfig.nrfx

@@ -79,6 +79,32 @@ config UART_ASYNC_TX_CACHE_SIZE
 	  in RAM, because EasyDMA in UARTE peripherals can only transfer data
 	  from RAM.
 
+config UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER
+	bool "Use TIMER to count RX bytes"
+	depends on UART_ASYNC_API
+	depends on UART_NRFX_UARTE_LEGACY_SHIM
+	depends on !ARCH_POSIX # Mode not supported on BSIM target
+	select NRFX_GPPI
+
+config UART_NRFX_UARTE_BOUNCE_BUF_LEN
+	int "RX bounce buffer size"
+	depends on UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER
+	default 256
+	range 64 1024
+	help
+	  Buffer is used when workaround with bounce buffers is applied
+
+config UART_NRFX_UARTE_BOUNCE_BUF_SWAP_LATENCY
+	int "RX bounce buffer swap latency (in microseconds)"
+	depends on UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER
+	default 300
+	help
+	  Option decides how long before current bounce buffer is filled driver
+	  attempts to swap the buffer. It must be long enough to ensure that
+	  space following the buffer is not overwritten. Too high value results
+	  in more frequent buffer swaps so it impacts performance. Setting should
+	  take into account potential interrupt handling latency.
+
 config UART_NRFX_UARTE_DIRECT_ISR
 	bool "Use direct ISR"
 	default y if !MULTITHREADING
@@ -188,37 +214,25 @@ nrfx_uart_num = 137
 rsource "Kconfig.nrfx_uart_instance"
 endif
 
-config NRFX_TIMER0
+config NRFX_TIMER
 	default y
 	depends on UART_0_NRF_HW_ASYNC_TIMER = 0 \
 		|| UART_1_NRF_HW_ASYNC_TIMER = 0 \
 		|| UART_2_NRF_HW_ASYNC_TIMER = 0 \
-		|| UART_3_NRF_HW_ASYNC_TIMER = 0
-
-config NRFX_TIMER1
-	default y
-	depends on UART_0_NRF_HW_ASYNC_TIMER = 1 \
+		|| UART_3_NRF_HW_ASYNC_TIMER = 0 \
+		|| UART_0_NRF_HW_ASYNC_TIMER = 1 \
 		|| UART_1_NRF_HW_ASYNC_TIMER = 1 \
 		|| UART_2_NRF_HW_ASYNC_TIMER = 1 \
-		|| UART_3_NRF_HW_ASYNC_TIMER = 1
-
-config NRFX_TIMER2
-	default y
-	depends on UART_0_NRF_HW_ASYNC_TIMER = 2 \
+		|| UART_3_NRF_HW_ASYNC_TIMER = 1 \
+		|| UART_0_NRF_HW_ASYNC_TIMER = 2 \
 		|| UART_1_NRF_HW_ASYNC_TIMER = 2 \
 		|| UART_2_NRF_HW_ASYNC_TIMER = 2 \
-		|| UART_3_NRF_HW_ASYNC_TIMER = 2
-
-config NRFX_TIMER3
-	default y
-	depends on UART_0_NRF_HW_ASYNC_TIMER = 3 \
+		|| UART_3_NRF_HW_ASYNC_TIMER = 2 \
+		|| UART_0_NRF_HW_ASYNC_TIMER = 3 \
 		|| UART_1_NRF_HW_ASYNC_TIMER = 3 \
 		|| UART_2_NRF_HW_ASYNC_TIMER = 3 \
-		|| UART_3_NRF_HW_ASYNC_TIMER = 3
-
-config NRFX_TIMER4
-	default y
-	depends on UART_0_NRF_HW_ASYNC_TIMER = 4 \
+		|| UART_3_NRF_HW_ASYNC_TIMER = 3 \
+		|| UART_0_NRF_HW_ASYNC_TIMER = 4 \
 		|| UART_1_NRF_HW_ASYNC_TIMER = 4 \
 		|| UART_2_NRF_HW_ASYNC_TIMER = 4 \
 		|| UART_3_NRF_HW_ASYNC_TIMER = 4

drivers/serial/Kconfig.nrfx_uart_instance

@@ -18,6 +18,13 @@ config UART_$(nrfx_uart_num)_ASYNC
 	help
 	  This option enables UART Asynchronous API support on port $(nrfx_uart_num).
 
+config UART_$(nrfx_uart_num)_COUNT_BYTES_WITH_TIMER
+	bool
+	depends on $(dt_nodelabel_has_prop,uart$(nrfx_uart_num),timer)
+	depends on HAS_HW_NRF_UARTE$(nrfx_uart_num)
+	default y
+	imply UARTE_NRFX_UARTE_COUNT_BYTES_WITH_TIMER
+
 config UART_$(nrfx_uart_num)_ENHANCED_POLL_OUT
 	bool "Efficient poll out on port $(nrfx_uart_num)"
 	depends on !$(dt_nodelabel_bool_prop,uart$(nrfx_uart_num),endtx-stoptx-supported)