Add INA219 usermod support and update platformio.ini

platformio.ini

@@ -294,6 +294,8 @@ lib_deps =
   #For ADS1115 sensor uncomment following
     ; adafruit/Adafruit BusIO @ 1.13.2
     ; adafruit/Adafruit ADS1X15 @ 2.4.0
+  #For INA219 sensor uncomment following (requires maintainer approval before enabling globally)
+    ; adafruit/Adafruit INA219 @ 1.2.1
 
 extra_scripts = ${scripts_defaults.extra_scripts}
 

usermods/INA219_v2/usermod_ina219.h

@@ -0,0 +1,226 @@
+// #warning **** Included USERMOD_INA219 ****
+
+#pragma once
+
+#include <Arduino.h>   // WLEDMM: make sure that I2C drivers have the "right" Wire Object
+#include "wled.h"
+#include <Adafruit_INA219.h>
+
+/*
+ * Usermod for the INA219 I2C current/power sensor.
+ *
+ * Displays the following values in the Info tab:
+ *   - Bus Voltage  (V)
+ *   - Load Voltage (V)
+ *   - Current      (mA)
+ *   - Power        (mW)
+ *
+ * Configurable parameters (via WLED Settings > Usermods):
+ *   - enabled            : enable/disable the usermod
+ *   - i2cAddress         : I2C address (0x40, 0x41, 0x44, 0x45)
+ *   - readInterval-ms    : measurement interval in milliseconds
+ *   - shuntResistor-mOhm : shunt resistor value in milli-Ohm (default: 100 = 0.1 Ohm)
+ *   - maxCurrentRange-A  : maximum expected current (0.4, 1.0, or 2.0 A) — selects PGA gain
+ *   - busVoltageRange-V  : bus voltage range (16 or 32 V)
+ *
+ * Current and power are calculated directly from the shunt voltage:
+ *   I = V_shunt / R_shunt  (independent of internal INA219 calibration)
+ *
+ * Requires: adafruit/Adafruit INA219 @ 1.2.1  (uncomment in platformio.ini)
+ */
+
+class UsermodINA219 : public Usermod {
+private:
+  Adafruit_INA219 *ina219 = nullptr;
+
+  float shuntVoltage_mV = 0.0f;
+  float busVoltage_V    = 0.0f;
+  float current_mA      = 0.0f;
+  float power_mW        = 0.0f;
+  float loadVoltage_V   = 0.0f;
+
+  bool sensorFound  = false;
+  unsigned long lastMeasure = 0;
+
+  // Configurable settings
+  uint32_t readInterval       = 5000;   // ms between measurements
+  uint8_t  i2cAddress         = 0x40;   // INA219 I2C address
+  float    shuntResistor_mOhm = 100.0f; // shunt resistor in milli-Ohm (100 mOhm = 0.1 Ohm)
+  float    maxCurrentRange_A  = 2.0f;   // max expected current: 0.4, 1.0, or 2.0 A
+  uint8_t  busVoltageRange_V  = 32;     // bus voltage range: 16 or 32 V
+
+  // PROGMEM string keys for config
+  static const char _readInterval[];
+  static const char _i2cAddress[];
+  static const char _shuntResistor[];
+  static const char _maxCurrentRange[];
+  static const char _busVoltageRange[];
+
+  // Select Adafruit calibration preset matching the configured voltage/current range.
+  // This sets the correct PGA gain register in the INA219 Config register (BRNG + PG bits).
+  // Current and power are still computed manually from the shunt voltage for accuracy.
+  // Note: the Adafruit library has no 16V preset beyond 400 mA; for 16V + higher current
+  // setCalibration_16V_400mA() is the only available 16V option and is used for all 16V cases.
+  void applyCalibration() {
+    if (!ina219) return;
+    if (busVoltageRange_V <= 16) {
+      ina219->setCalibration_16V_400mA();
+    } else {
+      if (maxCurrentRange_A <= 1.0f)
+        ina219->setCalibration_32V_1A();
+      else
+        ina219->setCalibration_32V_2A();
+    }
+  }
+
+public:
+  UsermodINA219(const char *name, bool enabled) : Usermod(name, enabled) {}
+
+  void setup() override {
+    if (!enabled) {
+      initDone = true;  // mark as initialized so re-enabling via UI triggers (re)setup
+      return;
+    }
+
+    if (!pinManager.joinWire()) {  // WLEDMM: allocates global I2C pins and starts Wire
+      USER_PRINTLN(F("[INA219]: failed to join I2C bus."));
+      sensorFound = false;
+      initDone = true;
+      return;
+    }
+
+    // Re-create sensor object with (potentially updated) I2C address
+    if (ina219) { delete ina219; ina219 = nullptr; }
+    ina219 = new Adafruit_INA219(i2cAddress);
+
+    if (!ina219->begin()) {
+      USER_PRINTLN(F("[INA219]: sensor not found."));
+      delete ina219;
+      ina219 = nullptr;
+      sensorFound = false;
+      initDone = true;
+      return;
+    }
+
+    applyCalibration();
+    sensorFound = true;
+    USER_PRINTLN(F("[INA219]: sensor found."));
+    initDone = true;
+  }
+
+  void loop() override {
+    if (!enabled || !sensorFound || !initDone || !ina219) return;
+    if (strip.isUpdating()) return;
+
+    unsigned long now = millis();
+    if (now - lastMeasure < readInterval) return;
+    lastMeasure = now;
+
+    // Read raw voltages directly from the sensor
+    shuntVoltage_mV = ina219->getShuntVoltage_mV();
+    busVoltage_V    = ina219->getBusVoltage_V();
+
+    // Calculate load voltage, current and power manually using the configured shunt value.
+    // This gives correct results for any shunt resistor, independent of the INA219 calibration.
+    loadVoltage_V = busVoltage_V + (shuntVoltage_mV / 1000.0f);
+    if (shuntResistor_mOhm < 1.0f) {
+      // Guard against division by zero / near-zero shunt value (misconfigured)
+      USER_PRINTLN(F("[INA219]: shuntResistor-mOhm is invalid (<1). Skipping current/power calculation."));
+      current_mA = 0.0f;
+      power_mW   = 0.0f;
+    } else {
+      current_mA = shuntVoltage_mV / (shuntResistor_mOhm / 1000.0f);  // I = U / R
+      power_mW   = current_mA * loadVoltage_V;
+    }
+  }
+
+  void addToJsonInfo(JsonObject &root) override {
+    if (!enabled) return;
+
+    JsonObject user = root[F("u")];
+    if (user.isNull()) user = root.createNestedObject(F("u"));
+
+    if (!initDone) {
+      JsonArray arr = user.createNestedArray(F("INA219"));
+      arr.add(F("Initializing..."));
+      return;
+    }
+
+    if (!sensorFound) {
+      JsonArray arr = user.createNestedArray(F("INA219"));
+      arr.add(F("Not found"));
+      return;
+    }
+
+    JsonArray busV  = user.createNestedArray(F("INA219 Bus Voltage"));
+    busV.add(busVoltage_V);
+    busV.add(F(" V"));
+
+    JsonArray loadV = user.createNestedArray(F("INA219 Load Voltage"));
+    loadV.add(loadVoltage_V);
+    loadV.add(F(" V"));
+
+    JsonArray curr  = user.createNestedArray(F("INA219 Current"));
+    curr.add(current_mA);
+    curr.add(F(" mA"));
+
+    JsonArray pwr   = user.createNestedArray(F("INA219 Power"));
+    pwr.add(roundf(power_mW / 10.0f) / 100.0f);
+    pwr.add(F(" W"));
+  }
+
+  void addToConfig(JsonObject &root) override {
+    JsonObject top = root.createNestedObject(FPSTR(_name));
+    top[F("enabled")]                = enabled;
+    top[FPSTR(_readInterval)]        = readInterval;
+    top[FPSTR(_i2cAddress)]          = i2cAddress;
+    top[FPSTR(_shuntResistor)]       = shuntResistor_mOhm;
+    top[FPSTR(_maxCurrentRange)]     = maxCurrentRange_A;
+    top[FPSTR(_busVoltageRange)]     = busVoltageRange_V;
+    DEBUG_PRINTLN(F("[INA219] config saved."));
+  }
+
+  bool readFromConfig(JsonObject &root) override {
+    JsonObject top = root[FPSTR(_name)];
+    if (top.isNull()) {
+      DEBUG_PRINTLN(F("[INA219]: No config found. (Using defaults.)"));
+      return false;
+    }
+    bool configComplete = !top.isNull();
+
+    uint8_t oldAddress = i2cAddress;
+    bool    oldEnabled = enabled;
+
+    configComplete &= getJsonValue(top[F("enabled")],            enabled,              false);
+    configComplete &= getJsonValue(top[FPSTR(_readInterval)],    readInterval,        (uint32_t)5000);
+    configComplete &= getJsonValue(top[FPSTR(_i2cAddress)],      i2cAddress,          (uint8_t)0x40);
+    configComplete &= getJsonValue(top[FPSTR(_shuntResistor)],   shuntResistor_mOhm,  100.0f);
+    if (shuntResistor_mOhm < 1.0f) {
+      USER_PRINTLN(F("[INA219]: shuntResistor-mOhm clamped to minimum 1 mOhm."));
+      shuntResistor_mOhm = 1.0f;
+    }
+    configComplete &= getJsonValue(top[FPSTR(_maxCurrentRange)], maxCurrentRange_A,   2.0f);
+    configComplete &= getJsonValue(top[FPSTR(_busVoltageRange)], busVoltageRange_V,   (uint8_t)32);
+
+    if (!initDone) {
+      DEBUG_PRINTLN(F("[INA219] config loaded."));
+    } else {
+      DEBUG_PRINTLN(F("[INA219] config (re)loaded."));
+      if ((oldAddress != i2cAddress) || (!oldEnabled && enabled) || (enabled && !sensorFound)) {
+        setup();  // (re)initialize sensor: address changed, just enabled, or previously not found
+      } else if (enabled && sensorFound) {
+        applyCalibration();  // update PGA gain for new voltage/current range
+      }
+    }
+    return configComplete;
+  }
+
+  uint16_t getId() override { return USERMOD_ID_INA219; }
+};
+
+// PROGMEM string definitions
+const char UsermodINA219::_readInterval[]    PROGMEM = "readInterval-ms";
+const char UsermodINA219::_i2cAddress[]      PROGMEM = "i2cAddress";
+const char UsermodINA219::_shuntResistor[]   PROGMEM = "shuntResistor-mOhm";
+const char UsermodINA219::_maxCurrentRange[] PROGMEM = "maxCurrentRange-A";
+const char UsermodINA219::_busVoltageRange[] PROGMEM = "busVoltageRange-V";

wled00/const.h

@@ -152,6 +152,7 @@
 #define USERMOD_ID_WIREGUARD             41     //Usermod "wireguard.h"
 #define USERMOD_ID_INTERNAL_TEMPERATURE  42     //Usermod "usermod_internal_temperature.h"
 #define USERMOD_ID_LDR_DUSK_DAWN         43     //Usermod "usermod_LDR_Dusk_Dawn_v2.h"
+#define USERMOD_ID_INA219                44     //Usermod "usermod_ina219.h"
 //WLEDMM
 #define USERMOD_ID_MCUTEMP               89     //Usermod "usermod_v2_artifx.h"
 #define USERMOD_ID_ARTIFX                90     //Usermod "usermod_v2_artifx.h"

wled00/usermods_list.cpp

@@ -185,6 +185,10 @@
 #include "../usermods/LDR_Dusk_Dawn_v2/usermod_LDR_Dusk_Dawn_v2.h"
 #endif
 
+#ifdef USERMOD_INA219
+#include "../usermods/INA219_v2/usermod_ina219.h"
+#endif
+
 //WLEDMM ARTIFX
 #ifdef USERMOD_ARTIFX
 #include "../usermods/artifx/usermod_v2_artifx.h"
@@ -383,6 +387,10 @@ void registerUsermods()
   usermods.add(new LDR_Dusk_Dawn_v2());
 #endif
 
+#ifdef USERMOD_INA219
+  usermods.add(new UsermodINA219("INA219", false));
+#endif
+
 
 // WLEDMM ARTIFX
 #ifdef USERMOD_ARTIFX